- 您现在的位置：买卖IC网 > Sheet目录1193 > AC244006 (Microchip Technology)KIT MPLAB REAL ICE TRACE
General Setup
4.7
4.8
SETTING THE EMULATOR AS THE DEBUGGER OR PROGRAMMER
Select Debugger>Select Tool>MPLAB REAL ICE to choose the MPLAB REAL ICE
in-circuit emulator as the debug tool. The Debugger menu and MPLAB IDE toolbar will
change to display debug options once the tool is selected. Also, the Output window will
open and messages concerning ICE status and communications will be displayed on
the MPLAB REAL ICE tab.
Select Programmer>Select Programmer>MPLAB REAL ICE to choose the MPLAB
REAL ICE in-circuit emulator as the programmer tool. The Programmer menu and
MPLAB IDE toolbar will change to display programmer options once the tool is
selected. Also, the Output window will open and messages concerning ICE status and
communications will be displayed on the MPLAB REAL ICE tab.
SETTINGS DIALOG
Select either Debugger>Settings or Programmer>Settings to open the Settings dialog
and set up the MPLAB REAL ICE in-circuit emulator.
4.8.1
Program Memory Tab
This tab of the Programmer dialog allows you to set up debug/programming options.
? Allow MPLAB REAL ICE to select memories and ranges – the emulator uses your
selected device and default settings to determine what to program.
? Manually select memories and ranges – you select the type and range of memory
to program.
TABLE 4-1:
Memories
Program
Configuration
EEPROM
ID
MANUAL SELECTION OPTIONS
Check to program Program Memory into target.
Check to program Configuration bits into target.
Note: This memory is always programmed when in Debug mode.
Check to erase and then program EEPROM memory on target, if
available. Uncheck to erase EEPROM memory on target.
Check to program ID Memory into target.
Program Options
Erase all before Program Check to erase all memory before programming begins.
Unless programming new or already erased devices, it is important
to have this box checked. If not checked, the device is not erased
and program code will be merged with the code already in the
device.
Program Memory
Start, End
? 2006 Microchip Technology Inc.
The starting and ending hex address range in program memory for
programming, reading, or verification.
If you receive a programming error due to an incorrect end
address, you need to perform a reconnect, correct the end address
and program again.
Note: The address range does not apply to the Erase function.
The Erase function will erase all data on the device.
DS51616A-page 25
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AC2626M6
PROBE TEMP 6" GENERAL PURP
AC300024
MOTOR STEPPER 2PHASE 8WIRE
AC300030
KIT ACOUSTIC ACCESSORY
ACM-16
CABLE MODULE FR3 16BIT 40-DIP
ACM-2X8
ACTIVE CABLE MODULE DUAL 8 BIT
ACM-8
CABLE MODULE FR3 8BIT 28/32-DIP
ACS9510EVB
EVALUATION BOARD FOR ACS9510
ACS9550EVB
EVALUATION BOARD FOR ACS9550
相关代理商/技术参数
AC244007
制造商:Microchip Technology Inc 功能描述:MPLAB REAL ICE JTAG ADAPTER - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:ADAPTER MPLAB REAL ICE JTA 制造商:Microchip Technology Inc 功能描述:ADAPTER, MPLAB, REAL, ICE, JTAG 制造商:Microchip Technology Inc 功能描述:ADAPTER, MPLAB, REAL, ICE, JTAG; Accessory Type:JTAG adaptor Board; For Use With:Microchip PIC32MX devices; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes
AC244008
功能描述:处理器配件 MPLAB REAL ICE Power Monitor
RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
AC244022
功能描述:插座和适配器 Procs Extnsn Pak for PIC24FJ128GA010-ICE RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244022
制造商:Microchip Technology Inc 功能描述:Processor Extension Pak for PI
AC244023
功能描述:插座和适配器 PROCESSOR EXTNSN PAK FOR PIC18F1xK50 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244024
功能描述:插座和适配器 Processor Ext Pak for PIC18LF14K50 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244026
功能描述:插座和适配器 Processor Ext Pak (PIC16F727-ICE) 200K RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244027
功能描述:插座和适配器 Processor Ext Pak (PIC16LF727-ICE)200K RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x